Hpe Failed to Upload Device Firmware Image

Transferring switch configurations

Using the CLI commands described in the section beginning with TFTP: Copying a configuration file to a remote host (CLI), you can copy switch configurations to and from a switch, or copy a software image to configure or replace an ACL in the switch configuration.

	NOTE: For greater security, yous tin perform all TFTP operations using SFTP, as described in the section Using SCP and SFTP. You can too use the include-credentials command to save passwords, underground keys, and other security credentials in the running config file. For more information, see the department on "Saving Security Credentials in a Config File" in the Access Security Guide for your switch.

TFTP: Copying a configuration file to a remote host (CLI)

Syntax:

copy <startup-config | running-config> tftp < ip-addr > < remote-file > [ pc | unix ]

copy config < filename > tftp < ip-addr > < remote-file > [ pc | unix ]

This command can re-create a designated config file in the switch to a TFTP server. For more information, see "Multiple Configuration Files" in the Basic Operation Guide for your switch.

Instance:

To upload the current startup configuration to a file named sw8200 in the configs directory on drive "d" in a TFTP server having an IP address of 10.28.227.105:

ProCurve# copy startup-config tftp 10.28.227.105    d:\configs\sw8200          

TFTP: Copying a configuration file from a remote host (CLI)

Syntax:

copy tftp <startup-config | running-config> < ip-address > < remote-file > [ pc | unix ]

copy tftp config < filename > < ip-address > < remote-file > [ pc | unix ]

This control can copy a configuration from a remote host to a designated config file in the switch. For more data, come across "Multiple Configuration Files" in the Basic Functioning Guide for your switch.

For more information on flash image use, run into "Using Primary and Secondary Flash Image Options" in the Basic Operation Guide for your switch.

Case:

To download a configuration file named sw8200 in the configs directory on drive "d" in a remote host having an IP accost of 10.28.227.105:

HP Switch# copy tftp startup-config 10.28.227.105    d:\configs\sw8200          

TFTP: Copying a customized command file to a switch (CLI)

Using the copy tftp control with the testify-tech option provides the ability to copy a customized control file to the switch. When the testify tech custom control is executed, the commands in the custom file are executed instead of the hard-coded listing of commands. If no custom file is found, the current difficult-coded listing is executed. This listing contains commands to brandish data, such as the image postage stamp, running configuration, kick history, port settings, and then on.

Syntax:

Using the re-create tftp show-tech command to upload a customized command file

HP Switch(config)# copy tftp bear witness-tech ten.10.10.3 commandfile1            

Syntax:

show tech custom

Executes the commands found in a custom file instead of the hard-coded listing.

	Notation: Exit the global config mode (if needed) before executing show tech commands.

You tin can include testify tech commands in the custom file, with the exception of show tech custom. For example, y'all can include the command show tech all.

If no custom file is found, a message displays stating "No SHOW-TECH file found." (No custom file was uploaded with the copy tftp show-tech command.)

The show tech custom command

HP Switch# show tech custom No Testify-TECH file constitute.            

Xmodem: Copying a configuration file to a serially connected PC or UNIX workstation (CLI)

To apply this method, the switch must exist connected via the serial port to a PC or UNIX workstation. You lot volition need to:

• Decide a filename to use.

• Know the directory path y'all volition utilise to store the configuration file.

Syntax:

copy <startup-config | running-config> xmodem <pc | unix>

re-create config < filename > xmodem <pc | unix>

Uses Xmodem to re-create a designated configuration file from the switch to a PC or UNIX workstation. For more information, see "Multiple Configuration Files" in the Basic Performance Guide for your switch.

Example:

To copy a configuration file to a PC serially continued to the switch:

1. Determine the file name and directory location on the PC.

2. Execute the following command:

   HP Switch# copy startup-config xmodem pc Printing 'Enter' and offset XMODEM on your host...                

3. Later on yous run across the higher up prompt, press [Enter] .

4. Execute the terminal emulator commands to begin the file transfer.

Xmodem: Copying a configuration file from a serially connected PC or UNIX workstation (CLI)

To use this method, the switch must be connected via the serial port to a PC or UNIX workstation on which is stored the configuration file y'all want to copy. To complete the copying, you need to know the name of the file to copy and the drive and directory location of the file.

Syntax:

re-create xmodem startup-config <pc | unix>

copy xmodem config < filename > < pc | unix>

Copies a configuration file from a serially connected PC or UNIX workstation to a designated configuration file on the switch.

For more information, see "Multiple Configuration Files" in the Basic Operation Guide for your switch.

Instance:

To copy a configuration file from a PC serially connected to the switch:

1. Execute the following command:

   HP Switch# re-create xmodem startup-config pc Device volition be rebooted, do you want to keep [y/north]? y Press 'Enter' and starting time XMODEM on your host...                

2. Afterward you see the above prompt, printing [Enter] .

3. Execute the final emulator commands to begin the file transfer.

4. When the download finishes, you lot must reboot the switch to implement the newly downloaded software. To do then, use ane of the following commands:

   Syntax:

   kick system flash [ principal | secondary ]

   boot arrangement flash [config < filename >]

   Switches boot from the designated configuration file. For more than information, come across "Multiple Configuration Files" in the Basic Operation Guide for your switch.

   Syntax:

   reload

   Reboots from the flash prototype currently in employ.

   (For more on these commands, encounter "Rebooting the Switch" in the Bones Functioning Guide for your switch.)

USB: Copying a configuration file to a USB device (CLI)

To use this method, a USB flash retention device must exist continued to the switch's USB port.

Syntax:

copy startup-config usb < filename >

copy running-config usb < filename >

Uses the USB port to copy a designated configuration file from the switch to a USB flash memory device. For more data, come across "Multiple Configuration Files" in the Basic Performance Guide.

Example:

To re-create the startup configuration file to a USB flash drive:

1. Insert a USB device into the switch'southward USB port.

2. Execute the following command:

   HP Switch# re-create startup-config usb HP Switch-config                

   where HP Switch-config is the proper name given to the configuration file that is copied from the switch to the USB device.

USB: Copying a configuration file from a USB device (CLI)

To use this method, the switch must be connected via the USB port to a USB wink bulldoze on which is stored the configuration file you want to re-create. To execute the command, you volition need to know the proper name of the file to copy.

Syntax:

copy usb startup-config < filename >

Copies a configuration file from a USB device to the startup configuration file on the switch.

Example:

To copy a configuration file from a USB device to the switch:

1. Insert a USB device into the switch'southward USB port.

2. Execute the following control:

   HP Switch# re-create usb startup-config HP Switch-config                    

   where HP Switch-config is the name of the file to copy.

3. At the prompt, press [Enter] to reboot the switch and implement the newly downloaded software.

longwhan1977.blogspot.com

Source: https://techhub.hpe.com/eginfolib/networking/docs/switches/WB/15-18/5998-8162_wb_2920_mcg/content/ch09s04.html

Share this post